About
Play audio files with your Arduino in decent quality from SD card, only very few additional hardware required.
Features
- 8-Bit PWM output - no external DAC required
- 16-Bit emulation using 2x 8-Bit PWM output - requires only two resistors
- 62.500 kHz (fullrate) / 31.250 kHz (halfrate) sampling rate @ 16 MHz
- 31.250 kHz (fullrate) / 15.625 kHz (halfrate) sampling rate @ 8 Mhz
- PWM output is operating always at fullrate for easier filtering
- Mono, bridge and stereo mode
- RAM usage ~1.3 kByte
- ROM usage ~6.1 kByte
- Integrated SD library (minimal FAT only, optimized for low RAM usage and high performance)
- Works with most SD card shields that are hooked to SPI port
- Easy to use API: 1. init library, 2. select audio file, 3. call play, 4. call worker while audio is playing
- Supports SD and SDHC cards formated with FAT16 or FAT32
Restrictions
- Audio file must be converted prior use
- Audio files must reside in root directory of card
- File name of audio file must be in 8.3-format
- Audio file must reside completely non-fragmented on card
- Combination of fullrate and stereo actually leads to buffer underruns
- Minimum controller required: ATmega168. ATmega8 is too low on RAM.
Download
Latest version:
Old versions:
Presentation for SimpleSDAudio (German)
Usage
Quickstart guide
- Install library: Unzip all to your /libraries/ folder.
- Copy the file /libraries/SimpleSDAudio/examples/EXAMPLE.AFM to root folder of a freshly formated SD card (don't use quick format!).
- Connect SD card to your Arduino board (using shield or whatever, SD card's chip select should go to pin 4, all other to SPI pins).
- Connect a speaker or headphone via 100 ohm resistor in series to audio output pin (pin 9 on Arduinos with ATmega168/328, pin 44 on Arduinos with ATmega1280/2560). Connect other end of speaker to GND.
- Launch Arduino IDE and try example "BareMinimumWithDebug" first.
- You should hear the audio (plays just a few seconds). Activate serial monitor to find some information if it does not work. Maybe you have to adjust SD cards CS pin in sketch.
Software installation guide
Browse to your sketchbook location (see Arduino - File - Preferences). There should be a folder called /libraries/, if not, create a folder and name it exactly like that. Then extract the zip-file preserving the folders and put all into the "libraries" folder that you end up with a structure where the "example" folder is located here: /libraries/SimpleSDAudio/examples/. Now you can start Arduino IDE and find examples for the library under File - Examples - SimpleSDAudio.
To convert audio files for usage with this library read the next paragraph.
Preparation of SD card and conversion of audio files
The audio library uses a very trimmed SD library that uses the FAT only to find the start sector of the files. Therefore the file must be completely non-fragmented on the SD card. The best way to ensure this is to do a fresh and full format of the card (don't use quick format!). After formating the SD card, only copy new files on it. Don't delete files and avoid rename operations that creates file names that doesn't fit into 8.3 format (see http://en.wikipedia.org/wiki/8.3_filename ). All files must placed in root directory as folders are not supported by the audio library.
To convert audio files I suggest the use of SoX from http://sox.sourceforge.net .
Windows users
Windows users should download from there the ZIP distribution and unzip it to the libraries/SimpleSDAudio/tools folder. Afterwards they can drag and drop .wav files to the appropriate batch files to start the conversion. The converted files will end up in folder "converted".
Linux users
Linux users should compile SoX from source or use their favorite package manager to install SoX. I recommend to use the following line for conversions:
sox inputfile.wav --norm=-1 -e unsigned-integer -b 8 -r 31250 -c 1 -t raw outputfile.raw
Change the following according to your needs:
- For stereo change -c 1 to -c 2
- For full rate use -r 62500 @ 16MHz, -r 31250 @ 8 MHz
- For half rate use -r 31250 @ 16MHz, -r 15625 @ 8 MHz
The option --norm=-1 is used to avoid bad sounding clipping effects.
File name conventions
Even you could choose any filename and any extension, I suggest using an extension that shows audio rate and stereo or mono mode. In the batch-files I use the following:
- .AFM - Fullrate, mono
- .AFS - Fullrate, stereo
- .AHM - Halfrate, mono
- .AHS - Halfrate, stereo
Hardware setup
The SD card should be connected to the SPI port of the controller. The chip select pin from the card can be connected to any free digital pin, but if pin 4 is used on Arduinos you don't have to adjust the source code. Many shields with SD card support like Ethernet-Shield will work. You need pegel conversion circuits from 5V to 3.3V for most Arduinos (except those that run natively on 3.3V).
According your mode configuration, one or two pins are used for audio output. This pins can not be changed and are different between different Arduino boards. For ATmega168/328 based plattforms those are pins 9 and 10. For ATmega1280/2560 those are pins 44 and 45. For other plattforms look into the file SimpleSDAudio.h.
Be careful that the audio output pins are digital ports that carry a positive voltage between 0V and 5V. It is not a good idea to have a DC voltage at line-inputs or smaller speakers as there will be a steady current flow. Therefore at least a resistor and/or a capacitor should be connected in series. For a start use at least 100 ohm or a capacitor between 100nF and 100uF. For line inputs use a voltage divider or poti to reduce the voltage.
Build your own SD breadboard adapter
Follow those pictures to build a very cheap SD-card adapter.
Using pliers to bend one side of pins < shape. Don't bend other side.
Bend all 7 pins of one row, leave other row non bend. You should end up like this:
Solder single-row pinheader to non-bend (=still straight) double-row pinheader.
Place card in holder. Card contact should get connected to non-bend (=straight) pins.
Put everything in your breadboard (front-side view).
Put everything in your breadboard (back-side view).
API reference
Constants
Here is an overview of the constants used in the library.
#define SSDA_VERSIONSTRING "1.00" // Sound Mode Flags #define SSDA_MODE_FULLRATE 0x00 // 62.500 kHz @ 16 MHz, 31.250 kHz @ 8 MHz #define SSDA_MODE_HALFRATE 0x10 // 31.250 kHz @ 16 MHz, 15.625 kHz @ 8 MHz #define SSDA_MODE_MONO 0x00 // Use only 1st PWM pin #define SSDA_MODE_STEREO 0x01 // Use both PWM pins for stereo output #define SSDA_MODE_MONO_BRIDGE 0x02 // Use both PWM pins for more power // Error codes from SimpleSDAudio, see other sd_l*.h for more error codes #define SSDA_ERROR_NULL 0x80 // Null pointer #define SSDA_ERROR_BUFTOSMALL 0x81 // Buffer to small #define SSDA_ERROR_NOT_INIT 0x82 // System not initialized properly
Class name and default instance
class SdPlayClass { ... }
extern SdPlayClass SdPlay;
The name of the class is SdPlayClass. One instance is already created for use and is named SdPlay.
Public class functions
init()
boolean init(uint8_t soundMode);
Call this to initialze the library and set sound mode. This function will also aquire the needed buffer (if not already set manually using setWorkBuffer), initialize SD card and sets up all used pins.
A combination of the following flags must be provided as argument (combine via or-ing):
Sample rate setting flags
- SSDA_MODE_FULLRATE - 62.500 kHz @ 16 MHz, 31.250 kHz @ 8 MHz
- SSDA_MODE_HALFRATE - 31.250 kHz @ 16 MHz, 15.625 kHz @ 8 MHz
Output channel configuration flags
- SSDA_MODE_MONO - Use only 1st PWM pin
- SSDA_MODE_STEREO - Use both PWM pins for stereo output
- SSDA_MODE_MONO_BRIDGE - Use both PWM pins for more power
The function return true if successfull, false if an error occured. You can use getLastError() to retrieve the error code. Typical reasons for errors are wrong SD card connection or too low RAM (1k heap required) for internal buffer available.
setFile()
boolean setFile(char *fileName);
After init was successfull, call this to select audio file by providing the filename in 8.3 format.
The function return true if successfull, false if an error occured. You can use getLastError() to retrieve the error code. Typical reasons for errors are that the file was not found.
worker()
void worker(void);
Call this continually at least as long as the audio playback is running. This function fills the internal playback buffer by reading the next sectors from SD card. You can´t call this function too often, but a buffer underrun can occur when the time between two calls are too long.
play()
void play(void);
If audio is not playing, playing will be started. If it is already playing, it will start playing from zero again.
stop()
void stop(void);
Stops playback if playing, sets playposition to zero.
pause()
void pause(void);
Pauses playing if not playing, resumes playing if was paused.
setSDCSPin()
void setSDCSPin(uint8_t csPin);
Call this before init to set SD-Cards CS-Pin to other than default.
setWorkBuffer()
void setWorkBuffer(uint8_t *pBuf, uint16_t bufSize);
Call this if you want to use your own buffer (at least 1024 bytes, must be multiple of 512). Call this before init and then init will use this buffer instead using malloc to create its own.
deInit()
void deInit(void);
Call this to free resources like buffer, release SD card pins, audio interrupts and audio pins.
dir()
void dir(void (*callback)(char *));
Output the directory of the SD card. A pointer to a callback function must be provided. The callback function is called once for every file found in the root directory of the card. The strings contain zero-termination but no linefeeds.
Usage example:
...
// setup global callback function
void dir_callback(char *buf) {
Serial.println(buf);
}
...
// somewhere after initialization
SdPlay.dir(&dir_callback);
isStopped(), isPlaying(), isPaused()
boolean isStopped(void); boolean isPlaying(void); boolean isPaused(void);
Returns the current state of the playback. The function isStopped() can be used after issuing play() to determine when the playback has finished.
isUnderrunOccured()
boolean isUnderrunOccured(void);
Returns if the internal underrun-flag is set and clears it. If audio sounds strange or has dropouts, test if underruns are the cause.
getLastError()
uint8_t getLastError(void);
Retrieve the last error code and clears it. To analyse the error reason, take a look also at the files sd_l1.h and sd_l2.h of the library to find the meaning of the code.
FAQ
It does not compile
- Are you using the latest version of Arduino IDE?
- SimpleSDAudio_V1.00 need at least V1.0.1 of Arduino IDE.
- SimpleSDAudio_V1.01 need at least V1.0 of Arduino IDE (remove complete block with !Serial from examples when using with Arduino IDE V1.0).
SdPlay.init fails
- Have you selected the correct CS pin for your SD-card? Uncomment the line
// SdPlay.setSDCSPin(10);
in the examples and enter correct pin number here. - Your SD shield may be crap and SD communication is only possible with limited speed. Try commenting the line
SPSR |= (1 << SPI2X);
in function SD_L0_SpiSetHighSpeed(). If this doesn't help, comment out also the first line and try again. If then init works you have a bad SD card shield.